
- Home
- Services
- Stucco Installation
Commercial Stucco Installation in Peachtree City
For new commercial buildings, additions and re-clads in Peachtree City, we install traditional three-coat portland cement stucco over a properly lapped weather barrier, with lath, control joints and weep screed placed where the wall needs them.
- Three-coat cement stucco
- Weather barrier & lath
- Control joints & screed
- New work & re-clads
Request a commercial quote
Peachtree City commercial stucco & EIFS. Property managers, boards, owners & builders.
What goes on the wall before the first coat
Hard coat stucco is durable, impact resistant and well suited to busy commercial elevations, but only when the layers under it are right. Most failures we repair on older buildings trace back to installation: a weather barrier lapped the wrong way, no weep screed at the base, control joints left out to save time, or lath fastened short of the framing.
On Peachtree City projects we start with the substrate. We confirm the sheathing, install a two-layer weather barrier lapped shingle-fashion, and flash openings and transitions so water drains out and down. Expanded metal lath is fastened into the framing, and accessories go on next: weep screed at the base, casing beads at openings, corner aids and control joints laid out to break the wall into panels that can move without cracking.
Then we apply the scratch coat, brown coat and finish, giving each coat its cure time and moisture. Rushing the cure is a reliable way to get shrinkage cracks, so we build realistic cure time into the schedule we give the general contractor. The finish can be a traditional sand texture or a smoother modern look, in a color selected for the building.

Every layer of a commercial stucco wall
A finished three-coat wall is a little under an inch thick, but it is built from six separate parts. Skip one and the others cannot make up for it.
Weather-resistive barrier
Barrier lapped top over bottom, so water that gets past the stucco runs down and out instead of into the sheathing.
Metal lath
Self-furred lath fastened into the framing and held off the barrier, so the scratch coat wraps around it and locks in.
Weep screed & casing beads
A weep screed at the base lets water drain out; casing beads finish the edges at windows and storefronts with room for sealant.
Control & expansion joints
Joints break long elevations into panels and isolate floor lines, so building movement shows up at the joint instead of as random cracking.
Flashing & kick-outs
Head flashing over openings, parapet and coping details and kick-outs at roof-to-wall lines go in with the barrier, where they can be lapped correctly.
Three coats, properly cured
Scratch, brown and finish coats applied in sequence, with base coats kept damp and given time to cure before the next goes on.
New buildings, additions and re-clads
On new construction we coordinate with the general contractor, framer, window and storefront installers and roofer so barrier and flashing go in in the right order. On an addition, the new wall has to tie into the existing stucco without a visible seam, which means matching texture and planning a joint where old meets new.
A re-clad is the biggest job, and on an occupied building it is planned elevation by elevation: the failed cladding comes off, we inspect and replace damaged sheathing, then install a complete new system before moving on. If the existing stucco is sound and the goal is a new look, a recoat or color change may be all the building needs.
| Project | What’s involved | Key detail |
|---|---|---|
| New constructionWhole building | Barrier, lath, three coats | Flashing sequenced with trades |
| AdditionNew wing or tenant space | Full system on new framing | Texture tied into existing |
| Re-cladFailed cladding off | Sheathing checked, new system | Phased around occupants |
| Partial elevationOne facade or tower | New system to a clean break | Joint at a corner or band |
How a commercial stucco wall is built
Three-coat stucco takes time because each coat has to cure. Much of the schedule is curing, not labor, and that time is what makes the wall last.
Review & prepare
We review drawings and joint layout, check the sheathing, install the weather barrier from the bottom up and integrate it with window, storefront and roof flashing.
- Joint layout confirmed
- Barrier lapped correctly
- Kick-outs installed
Lath & accessories
Weep screed, casing beads, corner aids and control and expansion joints go on with the lath, fastened into the framing and laid out to suit each elevation.
- Screed set above grade
- Joints laid out by panel
- Lath fastened to framing
Three coats & cure
The scratch coat is scored and kept damp, the brown coat is floated flat and allowed to cure, then the finish coat sets the specified texture and color.
- Base coats moist-cured
- Cure time between coats
- Finish to the spec
Bidding new construction or a re-clad?
Bring us in before the windows go in. Flashing, barrier and joint details are easiest to get right early.
Three-coat stucco for Peachtree City projects
Hard coat stucco suits the ground floors and entrances that take the most wear on Peachtree City commercial buildings.
On village center storefronts, restaurant pads along the highway corridors and multifamily ground floors near cart parking, the bottom of the wall takes bumps, splashing and constant foot traffic. Three-coat cement stucco handles that better than a thin finish over foam, which is why many projects use it at grade even when the upper floors are EIFS.
Georgia’s summer heat affects how stucco cures. We plan coats around the weather and keep fresh work damp enough to cure properly instead of baking dry in the afternoon sun.
Panels & joints
Control joints laid out to the building’s geometry so cracking is controlled.
Cure in the heat
Coats scheduled and moist-cured around Georgia summer temperatures.
Tough at grade
Hard coat at storefronts and entrances where walls take impacts and splash.
- Peachtree City
- Highway 54 corridor
- Highway 74 corridor
- Kedron
- Braelinn
- Aberdeen
- Glenloch
- Fayetteville
- Tyrone
- Newnan
Stucco installation FAQ for Peachtree City
Questions general contractors, developers and owners ask about new stucco in Peachtree City.
Does a new stucco facade in Peachtree City need design approval?
How long does three-coat stucco take?
Why are control joints necessary?
Can you combine hard coat stucco with EIFS on the same building?
Can you work in a busy village center while it stays open?
Request a stucco installation quote in Peachtree City
Send the drawings or describe the project. We will review the details and send an itemized written quote.

